Troubleshooting Chery Indis That Won't Start | Common Causes & Solutions

By Brian Wong, Reviewed by: Kurt Niebuhr, Updated on March 3, 2024
1. Common Causes for Chery Indis Not Starting
1.1. Fuel Issues
1.1.1. Empty Fuel Tank
1.1.2. Clogged Fuel Filter
1.1.3. Faulty Fuel Pump
1.2. Electrical Issues
1.2.1. Dead Battery
1.2.2. Faulty Starter Motor
1.2.3. Ignition System Failure
1.3. Mechanical Issues
1.3.1. Broken Timing Belt
1.3.2. Engine Seizure
1.3.3. Faulty Crankshaft Position Sensor
2. Troubleshooting Solutions for Chery Indis Not Starting
2.1. Fuel Issues
2.1.1. Refill Fuel Tank
2.1.2. Replace Clogged Fuel Filter
2.1.3. Replace Faulty Fuel Pump
2.2. Electrical Issues
2.2.1. Jumpstart the Battery
2.2.2. Replace Faulty Starter Motor
2.2.3. Check and Replace Ignition System Components
2.3. Mechanical Issues
2.3.1. Replace Broken Timing Belt
2.3.2. Repair or Replace Seized Engine
2.3.3. Replace Faulty Crankshaft Position Sensor
3. Additional Tips for Troubleshooting Chery Indis Not Starting
3.1. Check the Starter Solenoid
3.2. Test the Alternator
3.3. Inspect the Spark Plugs
3.4. Check the Distributor Cap and Rotor
3.5. Verify the Engine Compression
3.6. Use a Diagnostic Scanner to Check for Error Codes
4. Chery Indis Model-Specific Troubleshooting Solutions
4.1. Chery Indis X1
4.1.1. Check the Battery Terminals for Corrosion
4.1.2. Inspect the Alternator Belt for Damage or Tension
4.1.3. Check the Fuel Injectors for Blockages
4.2. Chery Indis S18D
4.2.1. Verify the Engine Oil Level
4.2.2. Check the Engine Coolant Level
4.2.3. Inspect the Fuel Lines for Leaks
4.3. Chery Indis A15
4.3.1. Check the Air Filter for Blockages
4.3.2. Inspect the Throttle Body for Dirt or Debris
4.3.3. Check the Mass Air Flow Sensor for Faults
5. Preventive Maintenance Tips for Chery Indis
5.1. Regularly Change the Engine Oil and Filter
5.2. Replace the Air Filter as Needed
5.3. Inspect and Maintain the Braking System
5.4. Check and Maintain the Suspension System
5.5. Keep the Battery and Charging System in Good Condition
6. Chery Indis Generation-Specific Troubleshooting Solutions
6.1. First Generation Chery Indis (2005-2010)
6.1.1. Check the Fuel Lines for Blockages or Leaks
6.1.2. Inspect the Battery Terminals for Corrosion
6.1.3. Replace the Starter Motor if Necessary
6.2. Second Generation Chery Indis (2011-2015)
6.2.1. Check the Ignition Coils for Faults
6.2.2. Inspect the Timing Belt for Wear and Tear
6.2.3. Verify the Fuel Pressure with a Gauge
6.3. Third Generation Chery Indis (2016-Present)
6.3.1. Check the Engine Control Module (ECM) for Faults
6.3.2. Inspect the Camshaft Position Sensor for Damage
6.3.3. Verify the Crankshaft Position Sensor Signal
7. Professional Help for Troubleshooting Chery Indis Not Starting
7.1. Consult a Qualified Mechanic or Technician
7.2. Use a Professional Diagnostic Scanner
7.3. Seek Help from Chery Authorized Service Centers
8. Common Symptoms of Chery Indis Not Starting
8.1. Cranking But Not Starting
8.2. No Sound When Turning the Key
8.3. Clicking or Whirring Noise When Turning the Key
8.4. Engine Starts and Immediately Stalls
8.5. Slow Cranking and Difficulty Starting
9. Conclusion
9.1. Summary of Troubleshooting Solutions
9.2. Importance of Regular Maintenance
9.3. Final Thoughts and Recommendations
FAQ: Chery Indis Not Starting - Troubleshooting Guide and Solutions

1. Common Causes for Chery Indis Not Starting

1.1. Fuel Issues

1.1.1. Empty Fuel Tank

Empty Fuel Tank (Common Causes for Chery Indis Not Starting Fuel Issues)

One of the most common reasons why a Chery Indis won't start is due to an empty fuel tank. This can happen if the driver forgets to fill up the tank, or if there is a leak in the fuel system that causes the fuel to drain out. It can also occur if the fuel gauge is not working correctly and gives an inaccurate reading.

If the fuel tank is empty, the engine will not receive any fuel to ignite and start. The car may crank but fail to start or not produce any sound at all when turning the key. To determine if an empty fuel tank is the cause of the problem, the driver should check the fuel gauge and verify that there is fuel in the tank.

If the fuel tank is indeed empty, the driver should fill it up with the recommended fuel type for their Chery Indis. It is essential to use the correct fuel type to prevent damage to the engine and ensure optimal performance. Additionally, if the fuel tank was empty due to a leak in the fuel system, the driver should have it inspected and repaired by a qualified mechanic.

1.1.2. Clogged Fuel Filter

Clogged Fuel Filter (Common Causes for Chery Indis Not Starting Fuel Issues)

Another common cause for a Chery Indis not starting is a clogged fuel filter. The fuel filter's primary function is to prevent contaminants and debris from entering the engine and damaging it. Over time, the fuel filter can become clogged with dirt, debris, and other particles, restricting the flow of fuel to the engine.

If the fuel filter is clogged, the engine may not receive enough fuel to start or run correctly. The car may crank but not start or produce a weak engine sound before dying. In some cases, the engine may start and run, but the performance will be sluggish and inconsistent.

To determine if the fuel filter is clogged, the driver can inspect it visually or have it checked by a qualified mechanic. If the fuel filter is clogged, it will need to be replaced with a new one. It is essential to use the correct fuel filter for the Chery Indis to ensure it fits properly and performs optimally.

1.1.3. Faulty Fuel Pump

Faulty Fuel Pump (Common Causes for Chery Indis Not Starting Fuel Issues)

A faulty fuel pump is another common cause for a Chery Indis not starting. The fuel pump's primary function is to transfer fuel from the fuel tank to the engine at a consistent rate. Over time, the fuel pump can become worn or damaged, leading to a decrease in fuel pressure and flow.

If the fuel pump is faulty, the engine may not receive enough fuel to start or run correctly. The car may crank but not start or produce a weak engine sound before dying. In some cases, the engine may start and run, but the performance will be sluggish and inconsistent.

To determine if the fuel pump is faulty, the driver can have it checked by a qualified mechanic or perform a fuel pressure test. If the fuel pump is indeed faulty, it will need to be replaced with a new one. It is essential to use the correct fuel pump for the Chery Indis to ensure it fits properly and performs optimally.

1.2. Electrical Issues

1.2.1. Dead Battery

Dead Battery (Common Causes for Chery Indis Not Starting Electrical Issues)

A dead battery is a common cause of electrical issues that can prevent a Chery Indis from starting. The battery's primary function is to provide electrical power to the engine starter motor and other electrical components. Over time, the battery can become worn or damaged, leading to a decrease in power and eventual failure.

If the battery is dead, the engine may not receive enough power to start or run correctly. The car may produce a clicking sound when trying to start or no sound at all. In some cases, the engine may start, but the performance will be sluggish and inconsistent.

To determine if the battery is dead, the driver can perform a voltage test using a multimeter or have it checked by a qualified mechanic. If the battery is indeed dead, it will need to be replaced with a new one. It is essential to use the correct battery for the Chery Indis to ensure it fits properly and performs optimally.

To prevent a dead battery, drivers should regularly check the battery's voltage level and replace it when necessary. They should also avoid leaving the headlights or other electrical components on when the engine is not running, as this can drain the battery's power.

1.2.2. Faulty Starter Motor

Faulty Starter Motor (Common Causes for Chery Indis Not Starting Electrical Issues)

A faulty starter motor is a common cause of electrical issues that can prevent a Chery Indis from starting. The starter motor's primary function is to turn the engine over and start the combustion process. Over time, the starter motor can become worn or damaged, leading to a decrease in power and eventual failure.

If the starter motor is faulty, the engine may not start at all or may produce a clicking sound when trying to start. In some cases, the engine may start, but the performance will be sluggish and inconsistent.

To determine if the starter motor is faulty, the driver can perform a voltage test using a multimeter or have it checked by a qualified mechanic. If the starter motor is indeed faulty, it will need to be replaced with a new one. It is essential to use the correct starter motor for the Chery Indis to ensure it fits properly and performs optimally.

To prevent a faulty starter motor, drivers should regularly check the electrical system and replace the starter motor when necessary. They should also avoid leaving the headlights or other electrical components on when the engine is not running, as this can drain the battery's power and put additional strain on the starter motor.

1.2.3. Ignition System Failure

Ignition System Failure (Common Causes for Chery Indis Not Starting Electrical Issues)

The ignition system is a critical component of a Chery Indis's electrical system, responsible for starting the combustion process that powers the engine. A failure in the ignition system can prevent the engine from starting or cause it to run poorly.

One of the most common causes of ignition system failure is a faulty ignition coil. The ignition coil converts the low voltage from the battery into the high voltage necessary to create a spark in the spark plugs, which ignite the fuel in the engine. If the ignition coil is faulty, it will not produce the necessary voltage to create a spark, preventing the engine from starting.

Another common cause of ignition system failure is a worn or faulty spark plug. Spark plugs can become fouled or corroded over time, reducing their ability to create a spark. This can lead to poor engine performance or an engine that fails to start.

To diagnose ignition system failure, drivers can perform a visual inspection of the ignition components, looking for signs of wear or damage. They can also use a multimeter to test the electrical components and determine if they are producing the necessary voltage. A qualified mechanic can also perform a diagnostic test on the ignition system to identify the cause of the failure.

To prevent ignition system failure, drivers should regularly inspect and replace the ignition components, including the ignition coil, spark plugs, and spark plug wires. They should also avoid driving with a misfiring engine, as this can cause damage to the catalytic converter and other components.

1.3. Mechanical Issues

1.3.1. Broken Timing Belt

Broken Timing Belt (Common Causes for Chery Indis Not Starting Mechanical Issues)

The timing belt is a critical component of a Chery Indis's engine, responsible for synchronizing the rotation of the crankshaft and camshaft to ensure the proper timing of the engine's valves and pistons. A broken timing belt can cause serious damage to the engine and prevent it from starting.

One of the most common causes of a broken timing belt is a failure to replace it at the recommended intervals. Timing belts are made of rubber and can degrade over time, becoming brittle and prone to breakage. If the timing belt breaks while the engine is running, it can cause the pistons to collide with the valves, resulting in costly engine damage.

Another common cause of timing belt failure is oil contamination. If oil leaks onto the timing belt, it can weaken the rubber and cause it to break prematurely. This can also cause damage to other engine components, such as the water pump and camshaft.

To diagnose a broken timing belt, drivers can perform a visual inspection of the timing belt and related components, looking for signs of wear or damage. If the timing belt is broken, the engine will not start or may make unusual noises when attempting to start.

To prevent timing belt failure, drivers should follow the manufacturer's recommended maintenance schedule and have the timing belt replaced at the recommended intervals. They should also address any oil leaks promptly and have them repaired to prevent contamination of the timing belt.

1.3.2. Engine Seizure

If your Chery Indi is not starting, there are many possible causes, and one of them could be engine seizure. Engine seizure occurs when the engine gets locked up and cannot rotate, which can happen due to a lack of lubrication, overheating, or other mechanical failures. Here are some common causes of engine seizure in Chery Indis:

1. Lack of Lubrication: The engine's moving parts need to be lubricated to prevent friction and heat buildup. If there is a lack of lubrication due to low oil pressure or a broken oil pump, the engine's moving parts can rub against each other, causing excessive heat and eventually seizing the engine.

2. Overheating: If the engine gets too hot, it can cause the metal to expand, which can cause it to seize. Overheating can be caused by a malfunctioning cooling system, such as a faulty water pump, a clogged radiator, or a broken thermostat.

3. Mechanical Failure: Any number of mechanical failures can cause the engine to seize, including broken connecting rods, damaged pistons, or a broken crankshaft. These failures can be caused by wear and tear or lack of maintenance.

If you suspect that engine seizure is the cause of your Chery Indi not starting, it is best to seek professional help immediately. Attempting to start a seized engine can cause further damage to the engine or even cause it to explode. A professional mechanic can diagnose the cause of the engine seizure and advise on the best course of action, which could involve engine rebuild or replacement. Regular maintenance of the engine, including regular oil changes and inspections, can help prevent engine seizure and ensure a longer lifespan for your Chery Indi.

1.3.3. Faulty Crankshaft Position Sensor

The crankshaft position sensor is an essential component of a Chery Indis's engine management system, responsible for monitoring the engine's rotational speed and position. If the sensor fails or malfunctions, it can cause a range of issues, including failure to start. Here are some common causes for Chery Indis not starting due to a faulty crankshaft position sensor:

1. Malfunctioning Sensor: Over time, the crankshaft position sensor can become worn or damaged due to prolonged use, heat, or exposure to debris. A malfunctioning sensor can send incorrect signals to the engine's control unit, causing the engine to not start or stall while driving.

2. Loose Connections: The crankshaft position sensor is connected to the engine's wiring harness through a connector plug. If the plug becomes loose or corroded, the sensor may not work properly, leading to issues such as engine stalling or failure to start.

3. Wiring Issues: The wiring leading to the crankshaft position sensor can become damaged or corroded, leading to incorrect signals being sent to the engine control unit. This can cause the engine to not start or stall while driving.

4. Failed Control Unit: In rare cases, the engine control unit itself may be faulty and fail to process the signals sent by the crankshaft position sensor. This can result in engine failure to start or stall while driving.

If you suspect that the crankshaft position sensor is causing your Chery Indis to not start, it is important to take your vehicle to a qualified mechanic for diagnosis and repair. They will be able to use specialized diagnostic equipment to determine the exact cause of the issue and recommend the necessary repairs or replacements.

2. Troubleshooting Solutions for Chery Indis Not Starting

2.1. Fuel Issues

2.1.1. Refill Fuel Tank

One of the most common reasons why a Chery Indis may not start is due to fuel-related issues. One possible cause of this issue is an empty fuel tank. If the fuel tank is empty, the fuel pump won't be able to draw fuel from the tank to the engine, resulting in the car not starting.

To troubleshoot this issue, the first step is to check the fuel gauge to see if the fuel tank is indeed empty. If the fuel gauge is faulty or inaccurate, it's best to manually check the fuel level by opening the fuel cap and visually inspecting the fuel level. If the fuel tank is empty, the solution is to refill the tank with enough fuel to start the car.

It's important to note that running a car with an empty fuel tank can cause damage to the fuel pump, as the fuel pump relies on fuel for lubrication and cooling. If the fuel pump is damaged, it may need to be replaced, which can be a costly repair. Therefore, it's important to always keep the fuel tank at least a quarter full to prevent damage to the fuel pump and ensure the car starts properly.

Additionally, it's also important to ensure the fuel being used is of good quality and free of contaminants. Using contaminated fuel can cause damage to the fuel filter and injectors, which can lead to starting issues and other engine problems. If the fuel tank was recently refilled, and the car still won't start, it may be worth checking the fuel quality or having the fuel system inspected for any damage or clogs.

2.1.2. Replace Clogged Fuel Filter

A clogged fuel filter can often be the culprit when a Chery Indis fails to start. The fuel filter is designed to prevent dirt, debris, and other contaminants from entering the fuel system and causing damage to the engine. Over time, however, the fuel filter can become clogged with these contaminants, reducing the flow of fuel to the engine and preventing the car from starting.

If you suspect that the fuel filter is clogged, there are a few troubleshooting solutions that you can try:

1. Check the fuel filter: First, locate the fuel filter in your Chery Indis. The location can vary depending on the model and year, so refer to your owner's manual or consult a mechanic if you're not sure where it is. Once you've located the filter, check to see if it's dirty or clogged. If it is, you'll need to replace it.

2. Replace the fuel filter: To replace the fuel filter, you'll need to purchase a new one and install it in place of the old filter. Again, refer to your owner's manual or consult a mechanic if you're not sure how to do this. Be sure to choose the right type of fuel filter for your car, as different models may require different types.

3. Test the fuel system: Once you've replaced the fuel filter, turn the ignition key and listen for the sound of the fuel pump. If you hear it running, the fuel system is likely working properly. If you don't hear anything, there may be a problem with the fuel pump or another component of the fuel system.

4. Check for other issues: If the fuel system seems to be working fine but the car still won't start, there may be other issues at play. Check the battery, starter motor, and ignition system to make sure they're all functioning properly.

By following these troubleshooting solutions, you should be able to diagnose and fix a clogged fuel filter in your Chery Indis. Regular maintenance, such as changing the fuel filter on a regular basis, can help prevent this issue from occurring in the future.

2.1.3. Replace Faulty Fuel Pump

If your Chery Indi is experiencing fuel-related starting issues and you have determined that the fuel pump is faulty, replacing it may be necessary to solve the problem. Here are some troubleshooting solutions for this issue:

1. Confirm that the fuel pump is the problem: Before replacing the fuel pump, it's important to confirm that it's the cause of the starting problem. You can do this by testing the fuel pressure with a fuel pressure gauge. If the pressure is too low or non-existent, then a faulty fuel pump is likely the issue.

2. Replace the fuel pump: If you have confirmed that the fuel pump is the problem, it will need to be replaced. This typically involves removing the fuel tank and replacing the pump assembly. It's recommended to have a professional mechanic perform this task as it can be difficult and dangerous to work with fuel.

3. Check for other issues: Sometimes a faulty fuel pump can be caused by other issues, such as a clogged fuel filter or a faulty fuel pressure regulator. Before replacing the fuel pump, it's a good idea to check for these other issues and address them as necessary.

4. Prevent future fuel pump issues: To prevent future fuel pump issues, it's important to ensure that you are using high-quality fuel and regularly changing the fuel filter. This will help to prevent debris and contaminants from damaging the fuel pump.

By following these troubleshooting solutions, you can solve the problem of a faulty fuel pump in your Chery Indi and prevent future fuel-related starting issues.

2.2. Electrical Issues

2.2.1. Jumpstart the Battery

If your Chery Indis won't start due to an electrical issue and the battery is dead, one solution is to jumpstart the battery. Jumpstarting the battery involves using another vehicle with a working battery to provide the necessary electrical charge to start the engine.

To jumpstart the battery, you will need a set of jumper cables and a second vehicle with a working battery. First, connect the red cable to the positive (+) terminal of the dead battery and then to the positive (+) terminal of the working battery. Next, connect the black cable to the negative (-) terminal of the working battery, and then to an unpainted metal surface of the dead vehicle, away from the battery and the fuel system.

Start the engine of the vehicle with the working battery and let it run for a few minutes. Then, try to start the engine of the Chery Indis. If the engine starts, remove the cables in the reverse order of how you connected them. Start by removing the black cable from the unpainted metal surface of the dead vehicle, then from the negative (-) terminal of the working battery. Next, remove the red cable from the positive (+) terminal of the working battery, and finally from the positive (+) terminal of the dead battery.

It's important to note that jumpstarting a battery is a temporary solution and should not be relied upon as a long-term fix. If the battery repeatedly dies, it may need to be replaced. Additionally, if the battery is not the issue, it's important to diagnose the underlying electrical problem that is causing the battery to die in the first place.

2.2.2. Replace Faulty Starter Motor

If your Chery Indis is not starting due to electrical issues, a common culprit may be a faulty starter motor. The starter motor is responsible for turning the engine over and initiating the combustion process. If the starter motor is not functioning properly, it can prevent the engine from starting.

One of the most common signs of a faulty starter motor is a clicking sound when you turn the key in the ignition. This is an indication that the motor is not engaging with the flywheel properly. Another symptom is a grinding noise when starting the engine, which can indicate that the starter gear is not aligning correctly with the flywheel.

If you suspect that the starter motor is the cause of your Chery Indis not starting, it is important to have it inspected and replaced if necessary. In some cases, the issue may be with the starter solenoid rather than the motor itself. A qualified mechanic will be able to diagnose the issue and determine the best course of action.

Replacing a faulty starter motor typically involves removing the old motor and installing a new one. This is a complex procedure that requires specialized tools and knowledge, so it is best to leave it to a professional mechanic. They will be able to ensure that the new starter motor is properly aligned with the flywheel and that all connections are secure.

In addition to a faulty starter motor, other electrical issues that can cause a Chery Indis not to start include a dead battery, faulty alternator, and issues with the ignition system. It is important to have these components inspected and replaced if necessary to ensure that your vehicle is running smoothly and reliably.

2.2.3. Check and Replace Ignition System Components

When a Chery Indis experiences electrical issues that prevent it from starting, the problem could lie with the ignition system. The ignition system is responsible for generating the electrical spark that ignites the fuel in the engine. If any of the components of the ignition system fail, the engine may not start. Common components of the ignition system that can fail include the spark plugs, ignition coil, distributor cap, and rotor.

To troubleshoot the ignition system, start by checking the spark plugs. Over time, spark plugs can become worn, fouled, or damaged, preventing them from creating a spark. Remove each spark plug and inspect it for signs of wear or damage. If the spark plugs are in good condition, use a spark plug tester to check for a spark. If no spark is present, the problem could lie with the ignition coil.

The ignition coil is responsible for creating the high voltage electrical charge that powers the spark plugs. If the ignition coil fails, there will be no spark to ignite the fuel. Use a multimeter to test the ignition coil for continuity and resistance. If the ignition coil tests bad, it will need to be replaced.

Next, check the distributor cap and rotor. The distributor cap and rotor work together to distribute the electrical spark to the correct spark plug at the correct time. If the distributor cap or rotor is worn or damaged, it can prevent the engine from starting. Inspect the distributor cap and rotor for cracks, corrosion, or carbon buildup. If either component is damaged, it should be replaced.

2.3. Mechanical Issues

2.3.1. Replace Broken Timing Belt

A broken timing belt can cause the Chery Indis to not start. The timing belt is a critical component of the engine that controls the opening and closing of the engine's valves. If the timing belt breaks or slips, the engine's timing is thrown off, and the valves can collide with the pistons, causing severe damage to the engine.

To troubleshoot a broken timing belt, a mechanic will need to inspect the timing belt and related components, such as the timing belt tensioner and idler pulleys, to see if there is any damage or wear. If the timing belt is broken or shows signs of wear, it will need to be replaced.

Replacing the timing belt is a complex and time-consuming job that should only be done by a trained mechanic. The mechanic will need to remove several components to gain access to the timing belt, including the engine cover, accessory drive belts, and timing belt cover. They will then need to remove the old timing belt and inspect the tensioner and idler pulleys for wear or damage. If the tensioner or idler pulleys are worn or damaged, they will need to be replaced as well.

Once the new timing belt and related components are installed, the mechanic will need to adjust the tension on the timing belt to ensure that it is properly aligned and tensioned. This is critical to ensure that the engine runs smoothly and that the timing belt does not slip or break again.

Regular maintenance of the timing belt is essential to prevent a broken timing belt from causing the Chery Indis to not start. The manufacturer's recommended maintenance interval for the timing belt should be followed, and the timing belt should be inspected for wear or damage during each maintenance service.

2.3.2. Repair or Replace Seized Engine

If your Chery Indis is not starting due to a seized engine, you may need to consider either repairing or replacing it. A seized engine can occur due to a variety of reasons, including low oil pressure, overheating, or lack of maintenance. When an engine seizes, the internal parts lock up, making it impossible for the engine to turn over.

To troubleshoot a seized engine, you can start by checking the oil level and condition. If the oil level is low or if it has not been changed for a long time, it can cause the engine to seize. If the oil looks dirty or contaminated, it may also indicate that there are internal engine problems. In such cases, it is recommended to take the car to a professional mechanic who can diagnose and repair the issue.

In some cases, a seized engine may require a complete replacement. This can be an expensive process, and it is important to consider the age and condition of the vehicle before making the decision. If the car is relatively new and has been well-maintained, it may be worth repairing the engine. However, if the car is older and has significant wear and tear, it may be more cost-effective to replace the vehicle instead.

To prevent engine seizure in the future, it is essential to keep up with regular maintenance and ensure that the oil is changed on time. If you notice any warning signs, such as strange noises or engine overheating, it is important to address the issue promptly to avoid further damage to the engine.

2.3.3. Replace Faulty Crankshaft Position Sensor

The crankshaft position sensor is an important component in the Chery Indis engine's mechanical system. It is responsible for providing information to the engine's computer about the position and speed of the crankshaft, which helps the computer determine when to ignite the spark plugs and inject fuel into the engine. If the sensor is faulty, the computer may not receive accurate information, which can cause problems with starting the engine.

One way to troubleshoot a faulty crankshaft position sensor is to use a diagnostic tool to read the engine's error codes. If the sensor is malfunctioning, the diagnostic tool will indicate a fault code related to the sensor. Another way to test the sensor is to use a voltmeter to check the sensor's voltage output.

If the sensor is found to be faulty, it will need to be replaced. The replacement process will typically involve removing the old sensor and installing a new one in its place. It's important to ensure that the new sensor is compatible with the Chery Indis model and engine type.

Replacing a faulty crankshaft position sensor can be a challenging task, and it's recommended to seek the help of a professional mechanic. A trained mechanic will have the necessary tools and expertise to safely and effectively replace the sensor, ensuring that the engine is running smoothly and efficiently.

3. Additional Tips for Troubleshooting Chery Indis Not Starting

3.1. Check the Starter Solenoid

The starter solenoid is an important component of the starter system that can sometimes cause a no-start issue in a Chery Indis. The solenoid is responsible for engaging the starter motor with the engine flywheel when the ignition key is turned. A faulty solenoid can prevent the starter motor from functioning properly, resulting in a no-start condition.

To check the starter solenoid, start by checking the battery to ensure it is fully charged and in good condition. Then, locate the starter solenoid, which is typically mounted on the starter motor or somewhere near the battery. Use a multimeter to test the solenoid's terminals for continuity and voltage. If there is no continuity or voltage, then the solenoid is faulty and needs to be replaced.

Another way to test the starter solenoid is to bypass it with a jumper wire. To do this, disconnect the battery cables and connect a jumper wire from the positive terminal of the battery to the starter solenoid's positive terminal. Then, connect another jumper wire from the solenoid's negative terminal to the engine block. If the engine starts, then the solenoid is faulty and needs to be replaced.

If the starter solenoid is found to be faulty, it will need to be replaced with a new one. This can typically be done by removing a few bolts and disconnecting a few wires. Be sure to consult the vehicle's service manual for specific instructions on how to replace the solenoid.

It's important to note that a faulty starter solenoid is not the only possible cause of a no-start condition in a Chery Indis. Other issues, such as a dead battery, faulty starter motor, or ignition system failure, should also be considered and checked.

3.2. Test the Alternator

If you are troubleshooting a Chery Indis that won't start, it is important to test the alternator. The alternator is responsible for charging the battery and keeping the electrical system powered while the engine is running. If the alternator is faulty or not functioning properly, it can cause issues with starting the engine.

To test the alternator, you will need a multimeter. First, start the engine and let it idle for a few minutes. Then, turn off all electrical components such as lights and the radio. Next, connect the multimeter to the battery terminals and check the voltage reading. The voltage should be around 13.5 to 14.5 volts. If the voltage is below 13 volts, it could be a sign of a faulty alternator.

You can also perform a visual inspection of the alternator. Check for any signs of damage or wear on the alternator belt and pulleys. Look for any loose connections or corroded terminals. If you notice any issues, it may be time to replace the alternator.

In addition to testing the alternator, it is also important to check the battery. A weak or dead battery can also cause issues with starting the engine. You can test the battery with a multimeter or by taking it to an auto parts store for testing.

Overall, testing the alternator is an important step in troubleshooting a Chery Indis that won't start. By checking the alternator and battery, you can pinpoint the root cause of the issue and take the necessary steps to fix it.

3.3. Inspect the Spark Plugs

If your Chery Indis is not starting, inspecting the spark plugs is another helpful troubleshooting step. Spark plugs are crucial components of the ignition system that generate the spark to ignite the fuel in the engine's combustion chamber. If the spark plugs are worn out, fouled, or damaged, they may prevent the engine from starting or cause misfires.

To inspect the spark plugs, you'll need to remove them from the engine. Check each spark plug for signs of wear, such as erosion or carbon buildup on the electrode. A worn-out spark plug can cause misfires, reduced fuel efficiency, and difficulty starting the engine. If you notice any damage or signs of wear, you should replace the spark plug with a new one that matches your engine's specifications.

Additionally, check the spark plug wires for damage or wear. Over time, the wires can become brittle or cracked, which can cause electrical resistance and interfere with the spark. If you find any damaged wires, replace them with new ones.

Keep in mind that different types of spark plugs have different lifespans, so it's important to follow the manufacturer's recommendations for replacement intervals. If you're not sure how to inspect or replace the spark plugs in your Chery Indis, consult your owner's manual or seek professional assistance.

3.4. Check the Distributor Cap and Rotor

The distributor cap and rotor play an important role in the ignition system of a Chery Indis, so it's important to check them if you're having trouble starting your vehicle. The distributor cap is a plastic cover that sits on top of the distributor and has a series of contacts inside that transfer electricity from the ignition coil to the spark plugs. The rotor, which is mounted inside the distributor cap, spins around and makes contact with each contact point on the cap in turn, sending a spark to the appropriate spark plug.

Over time, the distributor cap and rotor can become worn or damaged, which can cause misfiring or a complete lack of spark, making it difficult or impossible to start the engine. If you suspect that the distributor cap or rotor is the cause of your Chery Indis not starting, you should visually inspect them for signs of wear, cracks, or damage. You can also use a multimeter to test for continuity and check the resistance of the wires.

If the distributor cap or rotor is found to be faulty, they should be replaced with new ones. It's important to use high-quality replacement parts that are designed specifically for your Chery Indis to ensure that they fit properly and function correctly. Regularly checking and replacing the distributor cap and rotor as needed can help prevent ignition system issues and ensure reliable starting of your Chery Indis.

3.5. Verify the Engine Compression

If your Chery Indis is not starting, one additional tip for troubleshooting is to verify the engine compression. Engine compression is the pressure generated during the engine's combustion cycle that is necessary for the engine to start and run properly. If there is low compression or no compression, it can cause starting issues.

To check the engine compression, you will need a compression tester. Start by removing the spark plugs from each cylinder. Then, attach the compression tester to the first cylinder and crank the engine over a few times. The gauge on the compression tester will show the amount of pressure in the cylinder. Repeat this process for each cylinder.

Ideally, the compression should be within a certain range for each cylinder. If the compression is low or significantly different from the other cylinders, it may indicate a problem with the engine's internal components, such as worn piston rings, worn valves, or a blown head gasket. In this case, further diagnosis and repairs will be necessary.

Checking the engine compression can be a useful diagnostic tool when troubleshooting starting issues with your Chery Indis. If you are unsure about performing this test yourself, it is best to consult a qualified mechanic.

3.6. Use a Diagnostic Scanner to Check for Error Codes

If you have tried all the basic troubleshooting steps and still can't figure out why your Chery Indis is not starting, using a diagnostic scanner to check for error codes may help. Most modern vehicles, including the Chery Indis, have an onboard diagnostic system that monitors various sensors and systems in the vehicle. If there is an issue with any of these sensors or systems, it will trigger an error code, which can be read using a diagnostic scanner.

To use a diagnostic scanner, you will need to connect it to the OBD-II port in your vehicle, which is usually located under the dashboard on the driver's side. Once the scanner is connected, you can turn on the ignition and follow the instructions on the scanner to read any error codes that are stored in the vehicle's computer.

The error codes will typically include a brief description of the problem, which can help you pinpoint the issue more accurately. For example, if the scanner shows a code related to the fuel system, you may need to focus your troubleshooting efforts on the fuel pump or fuel injectors. Similarly, if the code indicates an issue with the ignition system, you may need to check the spark plugs or ignition coils.

It's important to keep in mind that not all error codes will necessarily indicate a serious problem. Some codes may simply indicate a minor issue, such as a loose gas cap or a sensor that needs to be reset. However, it's always best to take any error codes seriously and address them promptly, as they can sometimes be a sign of more significant underlying issues.

4. Chery Indis Model-Specific Troubleshooting Solutions

4.1. Chery Indis X1

4.1.1. Check the Battery Terminals for Corrosion

If you are experiencing starting issues with your Chery Indis X1, one of the first things you should check are the battery terminals. Corrosion can accumulate on the terminals over time, leading to poor connectivity between the battery and the rest of the electrical system.

To check for corrosion, you'll need to pop the hood and locate the battery. The terminals are the metal clamps that connect to the battery posts. Check them for signs of white or green powdery substance or any other discoloration. If you see any signs of corrosion, you'll need to clean the terminals.

To clean the terminals, first, disconnect the negative (-) cable from the battery to avoid any electrical short circuits. Then, use a wire brush or sandpaper to clean the terminals until they are shiny and free of any corrosion or debris. You may also use a solution of baking soda and water to clean the terminals.

Once the terminals are clean, reconnect the negative cable, and try starting your Chery Indis X1. If the battery terminals were the issue, your car should start up with no problems. However, if the issue persists, you may need to look into other model-specific troubleshooting solutions for the Chery Indis X1 or take your car to a professional mechanic for further diagnosis.

4.1.2. Inspect the Alternator Belt for Damage or Tension

If your Chery Indis X1 is having trouble starting, it could be due to an issue with the alternator belt. The alternator belt is responsible for turning the alternator, which charges the battery while the engine is running. A damaged or loose belt can cause the alternator to not function properly, leading to a drained battery and difficulty starting the engine.

To check the alternator belt, first, locate it under the hood of the car. Check for any visible signs of damage, such as cracks or fraying. Additionally, check the tension of the belt by pressing down on it with your finger. It should have some give, but not be too loose.

If the belt appears damaged or too loose, it may need to be replaced. This can typically be done by loosening the tensioner pulley, removing the old belt, and installing a new one. However, if you're unsure how to do this yourself, it's recommended to take your car to a professional mechanic for service.

Regularly inspecting and maintaining your alternator belt can help prevent starting issues in your Chery Indis X1. If you notice any signs of damage or loosening, it's best to address them as soon as possible to avoid further problems.

4.1.3. Check the Fuel Injectors for Blockages

If your Chery Indis X1 is having trouble starting, one possible cause is blocked fuel injectors. Fuel injectors are responsible for spraying the correct amount of fuel into the engine, and if they become blocked, this can lead to issues with starting or running the engine.

To check the fuel injectors, you will need to remove them from the engine and inspect them for any signs of blockages or damage. You can also use a fuel injector cleaning kit to flush out any blockages and restore their proper function.

Another way to check the fuel injectors is to use a fuel pressure gauge to measure the fuel pressure in the fuel system. If the fuel pressure is low, this could be a sign that the injectors are not working properly.

It's also a good idea to inspect the fuel filter and fuel pump for any issues that could be causing problems with the fuel delivery system. A clogged fuel filter or faulty fuel pump can also prevent the engine from starting or running properly.

Overall, if you suspect that the fuel injectors are the cause of your Chery Indis X1's starting issues, it's important to have them inspected and cleaned or replaced as necessary to ensure proper engine function.

4.2. Chery Indis S18D

4.2.1. Verify the Engine Oil Level

If your Chery Indis S18D is not starting, one of the first things to check is the engine oil level. A low oil level can cause problems with the engine and prevent it from starting. To check the oil level, park the vehicle on a level surface and wait for the engine to cool down. Locate the oil dipstick and remove it from the engine. Wipe it clean with a cloth and reinsert it back into the engine. Then, remove it again and check the oil level on the dipstick. The oil level should be between the minimum and maximum marks on the dipstick.

If the oil level is low, add more oil to the engine using the appropriate type and viscosity recommended in your owner's manual. Be careful not to overfill the engine with oil, as this can cause damage to the engine. Additionally, if you notice that the oil level is consistently low, it may indicate a leak or other issue with the engine that should be inspected by a qualified mechanic.

4.2.2. Check the Engine Coolant Level

If your Chery Indis S18D is not starting, one of the things you should check is the engine coolant level. The engine coolant is essential in maintaining the engine's optimal temperature and preventing overheating. If the coolant level is low, it can cause the engine to overheat and lead to starting problems.

To check the engine coolant level, make sure the engine is cool, and the vehicle is parked on level ground. Locate the coolant reservoir under the hood and check the coolant level indicated on the reservoir. The level should be between the "minimum" and "maximum" marks.

If the coolant level is low, add a mixture of coolant and water to the reservoir, following the manufacturer's recommendations in the owner's manual. Make sure the cap is securely tightened to prevent any leaks.

It's also essential to inspect the radiator hoses for any signs of leaks or cracks. Damaged hoses can cause a loss of coolant, which can lead to overheating and starting issues.

If you notice any significant leaks or issues with the engine coolant system, it's best to have a professional mechanic diagnose and repair the problem to prevent any further damage to your vehicle's engine.

4.2.3. Inspect the Fuel Lines for Leaks

If your Chery Indis S18D is having trouble starting, it may be due to a fuel leak. Fuel leaks can occur in the fuel lines or in other parts of the fuel system. It is important to inspect the fuel lines for any signs of leaks, such as puddles of fuel under the car or the smell of fuel coming from the engine bay.

To inspect the fuel lines, start by turning off the engine and allowing it to cool down completely. Next, locate the fuel lines under the car and visually inspect them for any signs of damage or wear. Look for cracks, holes, or other signs of damage. If you find any damage, the fuel lines will need to be replaced.

If you don't see any obvious signs of damage, try gently squeezing the fuel lines with your hand. If you notice any soft spots or areas where the lines collapse easily, this could indicate a leak. Additionally, if you see any wet spots or signs of fuel around the fuel lines, this could also indicate a leak.

If you suspect that there is a fuel leak in your Chery Indis S18D, it is important to have it repaired as soon as possible. Fuel leaks can be dangerous and can cause a fire if not addressed promptly. Bring your car to a qualified mechanic to have the fuel system inspected and repaired if necessary.

4.3. Chery Indis A15

4.3.1. Check the Air Filter for Blockages

The air filter is an essential component in the Chery Indis A15's air intake system. It prevents dust, debris, and other particles from entering the engine and causing damage. Over time, the air filter can become clogged with dirt and debris, which can reduce the engine's performance and cause it to stall or not start at all.

To check the air filter, open the hood and locate the air filter housing. It is usually a large, rectangular or circular box that is connected to the engine with a duct or hose. Open the housing and remove the air filter. Inspect the filter for signs of dirt and debris. If the filter appears dirty or clogged, it should be replaced.

Replacing the air filter is a relatively simple process. Purchase a replacement filter that is designed for the Chery Indis A15 model, then follow the instructions in the vehicle's owner's manual to remove the old filter and install the new one. Be sure to close the air filter housing securely to prevent any debris from entering the engine.

Checking and replacing the air filter is an important maintenance task that should be performed regularly to ensure the smooth operation of the Chery Indis A15's engine. A dirty air filter can cause a reduction in engine power, decreased fuel efficiency, and even damage to other engine components. By keeping the air filter clean and functioning properly, you can help prevent these issues and extend the life of your vehicle's engine.

4.3.2. Inspect the Throttle Body for Dirt or Debris

If the Chery Indis A15 is not starting, it could be due to a dirty or clogged throttle body. The throttle body is responsible for regulating the amount of air that enters the engine, and if it is clogged with dirt or debris, it can cause problems with the engine starting.

To inspect the throttle body, you will need to remove the air intake hose and air filter box. The throttle body is located at the end of the intake hose where it connects to the engine. Use a flashlight to examine the inside of the throttle body and look for any signs of dirt, debris, or carbon buildup.

If you notice any buildup, you can clean the throttle body using throttle body cleaner and a clean cloth or brush. Be sure to follow the instructions on the cleaner carefully and avoid getting any cleaner on other engine components. After cleaning, reassemble the air intake hose and air filter box, and start the engine to see if the problem has been resolved.

In some cases, a clogged throttle body may require professional cleaning or replacement. If you are unsure how to proceed or suspect that the issue is more complex, it is recommended to consult a certified mechanic for further assistance.

4.3.3. Check the Mass Air Flow Sensor for Faults

The Mass Air Flow (MAF) sensor is an important component of the Chery Indis A15's engine management system. It measures the amount of air entering the engine and sends this information to the engine control module (ECM), which uses it to calculate the correct fuel injection and ignition timing. If the MAF sensor is faulty or not working correctly, it can cause a range of engine problems, including difficulty starting, poor idling, and reduced fuel efficiency.

To check the MAF sensor, first, disconnect the electrical connector and remove the sensor from the air intake system. Inspect the sensor for any signs of damage or wear, such as cracks, corrosion, or bent connectors. If the sensor appears to be in good condition, use a multimeter to check its resistance and compare the reading with the manufacturer's specifications. If the resistance is outside of the recommended range, the sensor may need to be replaced.

Another way to test the MAF sensor is to use a scan tool to read the sensor's output signal. With the engine running, observe the sensor's readings as the throttle is opened and closed. The sensor's output should increase smoothly and consistently as the throttle is opened. If the sensor's readings are erratic or do not change as expected, it may be faulty.

Regular maintenance of the MAF sensor and air intake system is important to prevent issues from developing. Keep the air filter clean and replace it regularly, and check the intake system for any leaks or blockages. Additionally, avoid using aftermarket air filters or intake systems that can cause issues with the MAF sensor's performance.

5. Preventive Maintenance Tips for Chery Indis

5.1. Regularly Change the Engine Oil and Filter

Regularly changing the engine oil and filter is one of the most important preventive maintenance tasks you can perform for your Chery Indis. Engine oil is responsible for lubricating the internal components of the engine, reducing friction, and preventing wear and tear. Over time, the engine oil becomes contaminated with dirt, debris, and other particles, reducing its effectiveness in protecting the engine.

To ensure your Chery Indis stays in good condition, it's recommended to change the engine oil and filter at least every 5,000 kilometers or as recommended by the manufacturer. This will help ensure that the engine oil remains clean and effective at protecting the engine. If you frequently drive in harsh conditions, such as extreme temperatures or dusty environments, you may need to change the engine oil more frequently.

When changing the engine oil, it's important to use the correct type and grade of oil recommended by the manufacturer. Using the wrong type of oil can lead to reduced performance and potentially cause damage to the engine. It's also important to replace the oil filter with a new one, as this helps remove contaminants from the engine oil.

Regularly changing the engine oil and filter is a simple and effective way to keep your Chery Indis running smoothly and prevent expensive repairs down the line. It's a good idea to keep track of when you last changed the oil and set a reminder for when the next oil change is due. This will help ensure that you stay on top of this important maintenance task and keep your Chery Indis running at its best.

5.2. Replace the Air Filter as Needed

Replacing the air filter regularly is an important part of maintaining the engine's health in your Chery Indis. The air filter prevents dirt, debris, and other particles from entering the engine and causing damage. Over time, the air filter can become clogged with these particles, restricting airflow to the engine and causing it to work harder than it needs to.

It is recommended to check the air filter every 12,000 miles or 12 months, whichever comes first, and replace it if it is dirty or damaged. However, if you live in an area with high levels of pollution or dust, you may need to replace it more frequently.

Replacing the air filter is a relatively simple task that can be done by most car owners with basic knowledge of car maintenance. First, locate the air filter housing, which is usually located near the engine. Open the housing and remove the old air filter. Check the housing and surrounding area for any debris or dirt and clean it if necessary. Then, install the new air filter and close the housing.

Regularly replacing the air filter can help improve the engine's performance, increase fuel efficiency, and extend the life of the engine. It is a simple and inexpensive way to keep your Chery Indis running smoothly.

5.3. Inspect and Maintain the Braking System

Regular inspection and maintenance of the braking system is crucial for ensuring safe driving and preventing costly repairs. It is recommended to inspect the brake pads, rotors, and calipers every 10,000 miles or as per the manufacturer's guidelines. Worn out brake pads or damaged rotors can lead to poor braking performance and even brake failure in extreme cases.

Additionally, it is important to regularly check the brake fluid level and condition. The brake fluid level should be maintained between the minimum and maximum markings on the reservoir, and the fluid should be clear and free of contaminants. If the brake fluid appears cloudy or has a brownish color, it may be time to replace the fluid.

It is also important to check the brake lines for signs of wear or damage. Any leaks or cracks in the brake lines can cause loss of brake pressure and increase the risk of accidents. Finally, make sure the parking brake is functioning properly and adjust it as needed.

By regularly inspecting and maintaining the braking system, you can ensure that your Chery Indis is safe to drive and prevent costly repairs down the line.

5.4. Check and Maintain the Suspension System

Checking and maintaining the suspension system is an important aspect of preventive maintenance for Chery Indis vehicles. The suspension system consists of various components such as springs, shock absorbers, and struts that work together to provide a smooth and comfortable ride, as well as ensure the vehicle's stability and control.

Regular inspection of the suspension system components is necessary to identify any wear or damage that could compromise the system's performance. Signs of a failing suspension system include a bumpy or uncomfortable ride, excessive bouncing, uneven tire wear, and a pulling sensation when turning.

To maintain the suspension system, it is essential to keep the vehicle's wheels properly aligned and balanced. Misaligned wheels can cause uneven tire wear, vibrations, and a decrease in fuel efficiency. Regularly rotating the tires and replacing them when necessary can also help extend the life of the suspension system.

Another crucial aspect of maintaining the suspension system is keeping the components lubricated. Lubrication helps reduce friction between the various components and prevents wear and damage. Regularly inspecting the suspension system components and replacing worn or damaged parts can also prevent further damage and improve overall vehicle performance.

5.5. Keep the Battery and Charging System in Good Condition

Keeping the battery and charging system in good condition is an essential part of preventive maintenance for Chery Indis vehicles. It's important to regularly check the battery terminals for corrosion and clean them as needed to ensure a good electrical connection. If the battery is more than three years old, it may be time to replace it.

The alternator is responsible for charging the battery and powering the electrical system while the engine is running. Regularly inspecting the alternator belt for damage or tension and replacing it as needed can help prevent charging system failure.

It's also important to periodically test the alternator output to ensure it is working properly. If the alternator is not charging the battery, it can lead to starting problems and other electrical issues.

Regularly checking and replacing the spark plugs, ignition coils, and other ignition system components as needed can also help ensure proper charging system function.

In addition to these specific components, it's important to maintain good overall electrical system health by keeping all connections clean and tight and addressing any electrical issues promptly. By following these preventive maintenance tips, Chery Indis owners can help keep their vehicles running smoothly and avoid costly repairs down the road.

6. Chery Indis Generation-Specific Troubleshooting Solutions

6.1. First Generation Chery Indis (2005-2010)

6.1.1. Check the Fuel Lines for Blockages or Leaks

The fuel lines in a Chery Indis (2005-2010) are an essential component of the vehicle's fuel delivery system. Over time, these fuel lines can become clogged with debris or develop leaks, which can result in reduced fuel efficiency and even engine damage if not addressed promptly.

To check for blockages or leaks in the fuel lines, first, inspect the lines themselves for any visible signs of damage or wear, such as cracks or bulges. Next, check the fuel filter for any signs of clogging, which can also cause blockages in the fuel lines.

If there are no visible signs of damage or blockages, use a fuel pressure gauge to check the fuel pressure in the system. If the pressure is lower than the manufacturer's recommended specifications, this could indicate a blockage in the fuel lines or a malfunctioning fuel pump.

If a leak is suspected, use a fuel leak detection kit to locate the source of the leak. Once the source of the leak is found, repair or replace the affected fuel line immediately to prevent further damage to the engine and ensure optimal fuel efficiency. It's important to address any issues with the fuel lines promptly to avoid potentially dangerous situations, such as fuel leaks or engine failure while driving.

6.1.2. Inspect the Battery Terminals for Corrosion

The battery terminals of a Chery Indis First Generation (2005-2010) should be inspected regularly for signs of corrosion. Corrosion can build up on the terminals over time, which can prevent the battery from delivering power to the car's electrical system. To inspect the battery terminals, first, open the hood of the car and locate the battery. Then, disconnect the negative terminal (black) first and then the positive terminal (red) using the appropriate tools. Inspect the terminals for signs of corrosion, which can appear as a white or greenish powdery substance. If corrosion is present, use a wire brush or terminal cleaner to remove it from the terminals. Once the terminals are clean, reconnect the positive terminal first and then the negative terminal, being careful not to overtighten the clamps. It is also recommended to apply a small amount of dielectric grease to the terminals to help prevent future corrosion. By inspecting and maintaining the battery terminals, you can help ensure the reliable operation of your Chery Indis.

6.1.3. Replace the Starter Motor if Necessary

The starter motor is an essential component of the Chery Indis's engine, responsible for turning the engine over when you turn the key in the ignition. Over time, the starter motor can wear out, leading to problems starting the engine or the starter motor failing altogether.

If you experience difficulty starting your Chery Indis or hear a grinding noise when you turn the key, it may be time to inspect the starter motor. Check for any visible damage, such as cracks or corrosion, as well as loose connections or wires. Additionally, you may want to test the starter motor's voltage and current to determine if it is functioning properly.

If the starter motor is found to be faulty or damaged, it will need to be replaced. It is important to replace the starter motor with a high-quality, OEM part specifically designed for the Chery Indis to ensure proper function and longevity. A faulty starter motor can lead to a range of issues, including engine damage and stalling while driving, so it is crucial to address any problems with the starter motor as soon as possible.

6.2. Second Generation Chery Indis (2011-2015)

6.2.1. Check the Ignition Coils for Faults

The ignition coils are an essential component of the Chery Indis engine's ignition system, responsible for supplying high voltage electricity to the spark plugs. If one or more ignition coils are faulty, it can result in engine misfires, decreased power, and reduced fuel efficiency. To check for faults, you can use an ignition coil tester or a multimeter to measure the resistance of each coil. If the resistance is outside of the recommended range or there is no resistance at all, the coil may need to be replaced. Additionally, you should inspect the ignition coil connector and wiring for signs of damage or wear. Loose connections or damaged wiring can cause issues with the ignition system and result in poor engine performance. Regularly checking and maintaining the ignition coils can help keep your Chery Indis running smoothly and prevent costly repairs down the road.

6.2.2. Inspect the Timing Belt for Wear and Tear

The timing belt is a crucial component of the engine in your second-generation Chery Indis. It synchronizes the camshaft and the crankshaft, ensuring that the engine's valves open and close at the correct time. Over time, the timing belt can become worn or stretched, which can lead to a loss of performance or even engine failure. To prevent this, it is important to inspect the timing belt regularly for signs of wear and tear.

Some common signs of a worn timing belt include cracking or fraying on the surface of the belt, as well as any signs of wear on the teeth or edges. If you notice any of these signs, it is important to have the timing belt replaced as soon as possible to prevent engine damage.

It is generally recommended that the timing belt is replaced every 60,000 to 100,000 kilometers, depending on the manufacturer's recommendations. However, it is important to consult your vehicle's owner's manual for specific recommendations for your Chery Indis.

Replacing the timing belt is a complex process that requires specialized knowledge and tools. It is important to have the timing belt replaced by a qualified mechanic to ensure that the job is done correctly and your engine is protected. By inspecting and replacing the timing belt when necessary, you can ensure that your second-generation Chery Indis runs smoothly and reliably for years to come.

6.2.3. Verify the Fuel Pressure with a Gauge

If your Second Generation Chery Indis (2011-2015) is experiencing fuel delivery issues, it is important to verify the fuel pressure with a gauge. Low fuel pressure can cause a variety of problems, including engine misfires, hesitation, and stalling.

To verify the fuel pressure, you will need a fuel pressure gauge that is compatible with your Chery Indis. The gauge should be connected to the fuel rail or fuel pressure test port, which is typically located near the fuel injectors.

With the fuel pressure gauge connected, turn the ignition key to the "on" position but do not start the engine. This will cause the fuel pump to prime the system and build up pressure. The fuel pressure gauge should display the pressure reading, which can vary depending on the specific model of your Chery Indis.

If the fuel pressure reading is below the manufacturer's specifications, this could indicate a problem with the fuel pump, fuel filter, fuel pressure regulator, or fuel injectors. A qualified mechanic should be consulted to diagnose and repair the issue.

Verifying the fuel pressure with a gauge can help identify and resolve fuel delivery issues in your Second Generation Chery Indis. Regular maintenance of the fuel system, including replacing the fuel filter at recommended intervals, can help prevent fuel pressure issues from occurring in the first place.

6.3. Third Generation Chery Indis (2016-Present)

6.3.1. Check the Engine Control Module (ECM) for Faults

The Engine Control Module (ECM) is the brain of the Chery Indis engine's control system. It receives data from various sensors and uses this information to make adjustments to various systems such as the fuel injectors, spark plugs, and more. When the ECM malfunctions, it can cause a variety of issues such as poor engine performance, stalling, and even complete engine failure.

To check the ECM for faults, a diagnostic scan tool is needed. The scan tool can retrieve trouble codes stored in the ECM's memory, which can help identify the specific issue. The codes can indicate problems with sensors, wiring, or even the ECM itself.

In addition to checking for trouble codes, it's also important to visually inspect the ECM and its connections for any signs of damage or corrosion. Any damaged or corroded connections should be repaired or replaced as needed.

If a fault is detected in the ECM, it may need to be replaced. However, it's important to note that simply replacing the ECM may not fix the issue if the root cause is a faulty sensor or wiring problem. Therefore, it's essential to thoroughly diagnose the issue and address any underlying problems before replacing the ECM.

6.3.2. Inspect the Camshaft Position Sensor for Damage

The camshaft position sensor is an essential component of the Chery Indis engine management system. It is responsible for monitoring the position of the camshaft and sending that information to the engine control module. This information is then used to determine the correct fuel injection and ignition timing.

If the camshaft position sensor becomes damaged or fails, it can cause a variety of engine problems, including misfires, stalling, and difficulty starting. Therefore, it is important to inspect the camshaft position sensor regularly and replace it if any damage is detected.

To inspect the camshaft position sensor, start by locating it in the engine compartment. On the Chery Indis, it is typically located near the camshaft on the cylinder head. Once located, inspect the wiring and connector for any damage or corrosion.

Next, use a multimeter to test the resistance of the sensor. The specific resistance values may vary depending on the model of Chery Indis, so consult the manufacturer's specifications for the correct values. If the resistance values are not within the specified range, the camshaft position sensor may need to be replaced.

In addition to regular inspections, it is also important to avoid unnecessary wear and tear on the camshaft position sensor. This includes avoiding rough driving and excessive idling, which can cause additional stress on the sensor.

By inspecting and maintaining the camshaft position sensor, you can ensure that your Chery Indis engine continues to run smoothly and efficiently.

6.3.3. Verify the Crankshaft Position Sensor Signal

The crankshaft position sensor is an essential component of the engine management system in the Chery Indis. It detects the rotation speed and position of the crankshaft, which helps the engine control module (ECM) to accurately control the ignition timing and fuel injection. A faulty crankshaft position sensor can cause a range of issues, including engine misfire, stalling, and difficulty starting.

To verify the crankshaft position sensor signal, a mechanic will typically use an oscilloscope or multimeter to measure the voltage and waveform of the sensor output signal. The signal should be a clean and consistent square wave with a specific voltage range. Any irregularities or inconsistencies can indicate a faulty sensor.

If a faulty crankshaft position sensor is detected, it should be replaced immediately to prevent further damage to the engine. It is recommended to use OEM parts to ensure proper compatibility and reliability. Additionally, it is crucial to follow the manufacturer's recommended maintenance schedule to prevent premature sensor failure.

7. Professional Help for Troubleshooting Chery Indis Not Starting

7.1. Consult a Qualified Mechanic or Technician

When it comes to troubleshooting a Chery Indis that won't start, it can be helpful to consult a qualified mechanic or technician. These professionals have the training and experience necessary to diagnose and repair complex automotive issues.

A qualified mechanic or technician can use specialized tools and equipment to perform diagnostic tests on the vehicle's various systems, such as the fuel system, ignition system, and electrical system. They can also access manufacturer-specific information and technical service bulletins that can provide valuable insights into common issues with Chery Indis models.

It's important to choose a mechanic or technician who is experienced working with Chery Indis vehicles specifically, as they will be best equipped to understand the unique nuances and potential issues that can arise with these vehicles. It's also important to ask for references or reviews from past customers to ensure that you are working with a reputable and trustworthy professional.

Overall, while it may be tempting to try to diagnose and repair issues with your Chery Indis on your own, consulting a qualified mechanic or technician can ultimately save you time, money, and frustration in the long run. They can help ensure that your vehicle is diagnosed and repaired correctly, and can provide valuable guidance on how to prevent similar issues from occurring in the future.

7.2. Use a Professional Diagnostic Scanner

If you're experiencing issues with your Chery Indis not starting, using a professional diagnostic scanner can help identify the root of the problem. A professional diagnostic scanner can read and interpret error codes from your car's onboard computer system, providing valuable insight into any potential issues that may be preventing your car from starting.

These scanners are typically more advanced than the basic code readers that are available for purchase, allowing for more detailed analysis and troubleshooting. They may also be able to communicate with various modules in your car's system, providing further insight into specific issues.

If you're not comfortable using a diagnostic scanner on your own, it's best to consult a qualified mechanic or technician who has experience with Chery Indis models. They can use the scanner to diagnose the issue and provide recommendations for repair. Additionally, a professional diagnostic scanner can also help ensure that any repairs made are effective, as the scanner can be used to verify that the issue has been resolved.

7.3. Seek Help from Chery Authorized Service Centers

If you have tried all the basic troubleshooting steps and still can't figure out why your Chery Indis won't start, it may be time to seek help from a professional. One option is to take your car to a Chery authorized service center. These centers have trained mechanics who specialize in Chery vehicles and have access to specialized tools and diagnostic equipment.

When you take your car to a Chery authorized service center, the mechanics will perform a thorough diagnostic check of your vehicle to identify the root cause of the problem. They will use specialized diagnostic tools and equipment to identify any faults or issues with your car's electronic systems, fuel system, engine, and other critical components.

Chery authorized service centers have access to up-to-date technical information, manuals, and parts, which makes them the best place to seek help when your Chery Indis won't start. They can perform repairs and maintenance that meet Chery's high standards, ensuring that your car is repaired to the manufacturer's specifications.

By seeking help from a Chery authorized service center, you can be assured that your vehicle is in the hands of trained professionals who understand Chery cars inside and out. They can quickly identify and fix the problem, saving you time and money in the long run.

8. Common Symptoms of Chery Indis Not Starting

8.1. Cranking But Not Starting

If your Chery Indis cranks but doesn't start, there could be several reasons behind it. Some of the most common reasons include a faulty fuel pump, clogged fuel filter, bad ignition coil, malfunctioning spark plugs, or a weak battery.

One of the first things to check is the fuel system. Start by verifying if there's enough fuel in the tank, and if the fuel pump is working properly. If the fuel pump is not delivering fuel to the engine, it may need to be replaced. A clogged fuel filter can also prevent fuel from reaching the engine and cause starting issues.

Another potential culprit could be a malfunctioning ignition system. Check the ignition coil, spark plugs, and spark plug wires for damage or wear and replace as needed. A weak battery can also cause starting problems, so make sure to check the battery voltage and connections.

Other factors that could contribute to a cranking but not starting problem include a faulty starter motor, a broken timing belt, or a malfunctioning engine control module (ECM). If you are unable to identify the root cause of the issue, it's recommended to seek help from a qualified mechanic or technician who has experience working with Chery Indis vehicles.

8.2. No Sound When Turning the Key

If you're experiencing no sound when turning the key on your Chery Indis, there are a few potential causes that could be contributing to the issue. One possibility is that the battery is dead or dying, which can prevent the electrical components from working properly. In this case, jump-starting the car or replacing the battery may be necessary.

Another potential cause could be a faulty starter motor or starter solenoid. If this is the case, the starter may need to be replaced in order for the car to start properly. A bad ignition switch could also be to blame, preventing the car from receiving power when the key is turned.

It's also possible that there is an issue with the car's electrical system, such as a blown fuse or a faulty alternator. If any of these components are not functioning properly, it can prevent the car from starting.

If you're experiencing no sound when turning the key on your Chery Indis, it's best to have a qualified mechanic or technician diagnose the issue to ensure that it is properly identified and resolved.

8.3. Clicking or Whirring Noise When Turning the Key

If you turn the key and hear a clicking or whirring noise, it could be a sign that the starter motor is failing. The clicking noise is usually a result of a weak battery, a faulty starter solenoid, or a worn-out starter motor.

The starter motor is responsible for turning the engine over and getting it started. If the starter motor is faulty, it won't be able to turn the engine over, and you will hear a clicking noise instead.

Another possible cause of the clicking or whirring noise could be a faulty starter solenoid. The solenoid is responsible for engaging the starter motor with the flywheel of the engine. If the solenoid is not working correctly, the starter motor won't engage, and you will hear a clicking noise.

Lastly, a weak battery can also cause the clicking noise. The starter motor requires a significant amount of electrical power to turn the engine over. If the battery is weak or dead, it won't be able to provide enough power to the starter motor, resulting in a clicking noise.

If you hear a clicking or whirring noise when turning the key, it's important to have your Chery Indis checked by a qualified mechanic or technician. They will be able to diagnose the issue and recommend the necessary repairs.

8.4. Engine Starts and Immediately Stalls

One of the common symptoms of Chery Indis not starting is when the engine starts but immediately stalls. This could be an indication of a problem with the fuel delivery system or the engine control module. The fuel system may not be supplying enough fuel to the engine, causing it to stall immediately after starting. The engine control module could also be malfunctioning, causing the engine to stall.

Other possible causes could include a clogged fuel filter, a faulty fuel pump, or a problem with the ignition system. A clogged fuel filter can restrict fuel flow to the engine, while a faulty fuel pump can prevent fuel from reaching the engine altogether. Problems with the ignition system, such as a faulty ignition coil or spark plug, can also cause the engine to stall immediately after starting.

If you experience this symptom, it is important to have your Chery Indis inspected by a qualified mechanic or technician to diagnose the underlying issue. They can use professional diagnostic equipment to identify the specific problem and recommend the necessary repairs to get your car running properly again.

8.5. Slow Cranking and Difficulty Starting

Another common symptom of a Chery Indis not starting is slow cranking and difficulty starting. This can be caused by a variety of factors, including a weak or dead battery, a faulty starter motor, or a worn-out ignition switch. If the battery is weak or dead, the engine may turn over slowly or not at all, and the headlights and other electrical components may be dim or not work at all. In this case, the battery may need to be recharged or replaced.

If the starter motor is faulty, it may not be able to turn the engine over, or it may turn over very slowly. A clicking or whirring noise may also be heard when attempting to start the engine. The starter motor may need to be replaced in this case.

A worn-out ignition switch can also cause slow cranking and difficulty starting. This can be identified by a lack of power to the starter motor or a lack of response when turning the key. The ignition switch may need to be replaced or repaired to resolve this issue.

It's important to address slow cranking and difficulty starting as soon as possible to avoid being stranded with a vehicle that won't start. A qualified mechanic or technician can diagnose and repair the underlying issue to get your Chery Indis running smoothly again.

9. Conclusion

9.1. Summary of Troubleshooting Solutions

In conclusion, troubleshooting solutions for a Chery Indis that won't start can vary depending on the specific generation and the symptoms being experienced. However, some common solutions include checking the battery, verifying the fuel pressure, inspecting the timing belt and sensors, and consulting a qualified mechanic or technician. It is also recommended to use a professional diagnostic scanner and seek help from Chery authorized service centers if necessary. By properly identifying and addressing the issue, it is possible to get the Chery Indis up and running again.

9.2. Importance of Regular Maintenance

Regular maintenance of your Chery Indis is crucial for keeping it in good condition and ensuring it starts and runs smoothly. Neglecting routine maintenance tasks can lead to problems such as poor fuel efficiency, decreased engine performance, and even complete engine failure.

It is important to follow the manufacturer's recommended maintenance schedule for your specific Chery Indis model. This includes regular oil changes, filter replacements, and inspections of components such as belts, hoses, and brakes.

Not only does regular maintenance keep your vehicle running smoothly, it can also help prevent more costly repairs down the road. By catching and addressing small issues early on, you can avoid the need for more expensive repairs later.

In addition to following the recommended maintenance schedule, it is also important to be aware of any changes in your vehicle's performance or behavior. If you notice any unusual sounds, vibrations, or other issues, it is important to have your vehicle inspected by a qualified mechanic as soon as possible.

By taking care of your Chery Indis and addressing any issues promptly, you can ensure that it continues to provide reliable transportation for years to come.

9.3. Final Thoughts and Recommendations

In conclusion, troubleshooting a Chery Indis that is not starting can be a complex process, and it is important to have a systematic approach to identify the root cause of the problem. By following the generation-specific troubleshooting solutions and seeking professional help from qualified mechanics or technicians, you can ensure that your Chery Indis is repaired correctly and efficiently.

Regular maintenance is also crucial to keep your vehicle in good working condition and prevent issues such as not starting. This includes changing the oil and air filters, checking the battery, and inspecting the spark plugs and ignition system.

It is important to note that attempting to diagnose and repair complex issues without the proper knowledge and tools can be dangerous and can cause further damage to your vehicle. Therefore, it is recommended to seek professional help when in doubt.

Overall, taking care of your Chery Indis and promptly addressing any issues can help ensure reliable and efficient performance.

FAQ: Chery Indis Not Starting - Troubleshooting Guide and Solutions

What are the common reasons for a Chery Indis not starting?

There can be various reasons for a Chery Indis not starting. The most common reasons include a dead battery, faulty starter motor, ignition system failure, fuel system issues, or a malfunctioning engine control module.

How can I tell if my Chery Indis has a dead battery?

If the engine doesn't crank and the lights on the dashboard are dim or flickering, it is a sign of a dead battery. Another way to tell is by turning on the headlights; if they are weak or do not turn on at all, then the battery is likely dead.

What should I do if my Chery Indis won't start due to a dead battery?

You can try jumpstarting the car using another vehicle with a working battery. If that doesn't work, then you may need to replace the battery with a new one.

How can I determine if my Chery Indis has a faulty starter motor?

If you turn the key and the engine doesn't crank, but you hear a clicking sound or a whirring noise, it may indicate a faulty starter motor. You can also have the starter motor tested by a mechanic to confirm the diagnosis.

What are some signs of an ignition system failure in a Chery Indis?

Signs of an ignition system failure include the engine cranking but not starting, or the engine starting and then immediately stalling. Additionally, if the dashboard lights do not turn on when you turn the key, it could indicate a problem with the ignition system.

What could be causing my Chery Indis to have fuel system issues and not start?

Fuel system issues can occur due to a clogged fuel filter, a malfunctioning fuel pump, or a faulty fuel injector. You may notice symptoms such as the engine cranking but not starting, or the engine starting and then immediately stalling.

How can I diagnose if my Chery Indis has an issue with the engine control module?

The engine control module (ECM) is responsible for controlling the engine's performance. If the ECM fails, it can cause the engine not to start. You can diagnose the issue by having the ECM scanned for error codes or by having a mechanic test it using diagnostic equipment.

Are there any recalls related to Chery Indis not starting?

As of the latest information available, there are no recalls related to Chery Indis not starting. However, it is always a good idea to check with your local dealership or manufacturer for any updates or recalls related to your specific vehicle.

How often should I have my Chery Indis serviced to prevent starting issues?

It is recommended to have your Chery Indis serviced at least once a year, or every 10,000 km, whichever comes first. Regular maintenance can help prevent starting issues by ensuring that the battery, starter motor, ignition system, and fuel system are all in good condition.

What should I do if my Chery Indis engine cranks but won't start?

If your Chery Indis engine cranks but won't start, there could be a few potential causes. Some common causes include a faulty fuel pump, a clogged fuel filter, a malfunctioning ignition coil, or a faulty spark plug. It's recommended to consult a qualified mechanic or technician to diagnose the exact cause and provide the necessary repairs.

What can cause my Chery Indis to make a clicking or whirring noise when turning the key?

A clicking or whirring noise when turning the key could be a sign of a weak battery, a faulty starter motor, or a bad alternator. It's recommended to check the battery connections, charge the battery, and test the starter and alternator. If the issue persists, it's best to seek professional help.

What should I do if my Chery Indis engine starts and immediately stalls?

If your Chery Indis engine starts and immediately stalls, it could be caused by a faulty crankshaft position sensor, a malfunctioning fuel injector, or a clogged fuel filter. It's recommended to consult a qualified mechanic or technician to diagnose the exact cause and provide the necessary repairs.

Why is my Chery Indis slow to crank and difficult to start?

A slow cranking engine or difficulty starting could be caused by a weak battery, a faulty starter motor, a clogged fuel filter, or a malfunctioning fuel pump. It's recommended to check the battery connections, charge the battery, and test the starter, fuel filter, and fuel pump. If the issue persists, it's best to seek professional help.

How often should I perform regular maintenance on my Chery Indis?

It's recommended to follow the manufacturer's recommended maintenance schedule, which can typically be found in the owner's manual. Regular maintenance tasks include oil changes, air filter replacements, and checking fluid levels. Following a regular maintenance schedule can help prevent potential issues with your Chery Indis and keep it running smoothly.

What should I do if my Chery Indis cranks but does not start?

If your Chery Indis cranks but does not start, it could be due to a variety of reasons. You may want to check the fuel pump, fuel injectors, spark plugs, battery, and other electrical components. It is recommended to have a qualified mechanic or technician diagnose the problem to properly identify the cause and make the necessary repairs.

How do I know if my Chery Indis has a bad starter?

If your Chery Indis does not make any sound when turning the key, it could be a sign of a bad starter. A clicking or whirring noise when turning the key may also indicate a bad starter. However, other issues such as a weak battery or a faulty ignition switch can also cause similar symptoms. It is recommended to have a qualified mechanic or technician diagnose the problem to properly identify the cause and make the necessary repairs.

Can a dead battery cause my Chery Indis not to start?

Yes, a dead battery can cause your Chery Indis not to start. The battery provides the electrical energy needed to start the engine. If the battery is weak or dead, it may not provide enough power to turn the starter motor and start the engine. You may want to check the battery voltage and charge it or replace it if necessary.

What should I do if my Chery Indis engine starts but stalls immediately?

If your Chery Indis engine starts but stalls immediately, it could be due to a variety of reasons. It may be caused by a faulty fuel pump, clogged fuel filter, or dirty fuel injectors. It could also be due to an issue with the ignition system, such as a faulty ignition coil or spark plugs. It is recommended to have a qualified mechanic or technician diagnose the problem to properly identify the cause and make the necessary repairs.

How can I prevent my Chery Indis from not starting in the future?

Regular maintenance and inspections can help prevent your Chery Indis from not starting in the future. It is recommended to follow the manufacturer's recommended maintenance schedule and have your vehicle inspected by a qualified mechanic or technician on a regular basis. This can help identify and address any potential issues before they become more serious and result in your vehicle not starting.

What should I do if my Chery Indis engine starts and immediately stalls?

If your Chery Indis engine starts and immediately stalls, it may be caused by a faulty crankshaft position sensor, a clogged fuel filter, or a malfunctioning fuel pump. You should take your car to a qualified mechanic or technician to diagnose and fix the issue.

What should I do if my Chery Indis is slow to crank and difficult to start?

If your Chery Indis is slow to crank and difficult to start, it may be caused by a weak battery, a faulty starter motor, or a clogged fuel filter. You should check the battery connections and have the battery tested, and also have the starter and fuel filter checked by a qualified mechanic or technician.

How often should I have my Chery Indis serviced to prevent starting problems?

It is recommended to have your Chery Indis serviced every 10,000 kilometers or every 6 months, whichever comes first. Regular maintenance, such as oil changes, filter replacements, and spark plug replacements, can help prevent starting problems and keep your car running smoothly.

Can a bad alternator cause my Chery Indis not to start?

Yes, a bad alternator can cause your Chery Indis not to start if it is not charging the battery properly. If the battery is not getting enough charge, it may not have enough power to start the engine. If you suspect your alternator is faulty, you should have it checked by a qualified mechanic or technician.

How do I know if my Chery Indis needs a new battery?

If your Chery Indis is slow to crank or won't start at all, it may be a sign that the battery needs to be replaced. You can also check the battery's voltage with a multimeter. A fully charged battery should read around 12.6 volts. If the voltage is lower than this, it may be time to replace the battery.

Can a faulty fuel pump cause my Chery Indis not to start?

Yes, a faulty fuel pump can cause your Chery Indis not to start if it is not delivering fuel to the engine properly. If the fuel pump is not functioning correctly, it may need to be replaced. You should have it checked by a qualified mechanic or technician.

How do I know if my Chery Indis has a bad starter motor?

If your Chery Indis is slow to crank or won't start at all, it may be a sign that the starter motor is faulty. You can check the starter motor by using a multimeter to measure the voltage at the starter solenoid when you turn the key. If there is voltage, but the starter motor does not turn, it may need to be replaced. You should have it checked by a qualified mechanic or technician.

Can a dirty air filter cause my Chery Indis not to start?

No, a dirty air filter is unlikely to cause your Chery Indis not to start, but it can affect engine performance and fuel efficiency. If the air filter is dirty, it can restrict airflow to the engine and cause it to run poorly. You should have the air filter checked and replaced as needed during regular maintenance.

What could be causing my Chery Indis to start and then immediately stall?

This issue could be caused by a variety of problems, including a faulty fuel pump, clogged fuel filter, or a malfunctioning ignition switch. It is best to have a qualified mechanic or technician diagnose and repair the issue.

Can a weak battery cause my Chery Indis to not start?

Yes, a weak or dead battery can prevent your Chery Indis from starting. It is recommended to have your battery tested regularly and replaced as needed.

How often should I replace my Chery Indis' spark plugs?

The recommended interval for replacing spark plugs on a Chery Indis can vary based on the model and year. It is best to consult your owner's manual or a qualified mechanic for the recommended maintenance schedule.

Can a malfunctioning starter cause my Chery Indis to not start?

Yes, a malfunctioning starter can prevent your Chery Indis from starting. Signs of a bad starter may include a clicking or whirring sound when turning the key, or slow cranking when attempting to start the engine.

Why is my Chery Indis cranking but not starting?

There are several potential causes for a Chery Indis to crank but not start, including a faulty fuel pump, a clogged fuel filter, a malfunctioning ignition switch, or a problem with the crankshaft position sensor.

What should I do if my Chery Indis won't start and I'm stranded on the road?

If your Chery Indis won't start and you're stranded on the road, it's best to call a tow truck to have your vehicle transported to a qualified mechanic or Chery authorized service center for diagnosis and repair.


Brian Wong - Senior Reviews Editor of cars-directory.net

Brian Wong / Author

Brian Wong is an accomplished automotive journalist and editor with a passion for cars. With over a decade of experience in the industry, he has established himself as a trusted voice in the automotive community. Brian has written extensively about a wide range of topics in the field, from the latest trends in car design to innovative safety features and emerging technologies. As a senior reviews editor, he is responsible for test driving and analyzing the latest cars on the market, providing readers with accurate and objective reviews. His articles are widely read and respected for their depth of knowledge and analysis. Brian is committed to staying at the forefront of the latest developments in the automotive industry, and is dedicated to sharing his expertise and insights with his readers.



Updated on March 3, 2024